Blog Right Sidebar – Page 15

Linux, Storage

How to Create LVM Volume Group and Logical Volume

Create LVM Volume Group and Logical Volume
Logical Volume Manager (LVM) is a device mapper target that provides logical volume management for the Linux kernel. LVM allows to create Logical Volumes from underlying Physical Hard Disks (Physiacal Volumes). Logical Volumes can be easily extended and shrunk according to the file system capacity demands.

LVM Objects:
Physical Volume (PV): underlying physical storage for LVM. These are most often physical hard disks, but also can be: partitions, RAID volumes, etc…
Volume Group (VG): storage pool, created from one or more Physical Volumes.
Physical Extent: small chunk of Physical Volume, used during Volume Group creation.
Logical Extent: mapped to Physical Extent, acting as front-end chunk for Logical Volumes.
Logical Volume: group of Logical Extents, used by the system as hard drive partition.
Read More

Linux, Security

Detect Intrusion and Check Linux File System Integrity with AIDE

Nov 11, 2015 by Grzegorz Juszczak 0 Comments advanced intrusion detection environment, aide detect intrusion linux, check file system integrity, detect intrusion with aide, linux aide detect intrusion, linux aide file integrity, linux detect intrusion aide, linux filesystem integrity check

If you suspect that your system was compromised and files and/or their permissions were modified by the intruder, you can use AIDE to check your file system against some modifications.

AIDE (Advanced Intrusion Detection Environment) is a file integrity checker and intrusion detection program. AIDE is used to scan the system when it’s in known good state – it collects information about files and their permissions in the file system and writes gathered information to the database. Once the database is initialized it can be used to verify the integrity of the files in case of some compromise is suspected. All of the usual file attributes can be checked for inconsistencies.

In this tutorial we will show you how to install and deploy AIDE on CentOS/Fedora/RedHat.
Read More

Linux

Display Hardware Topology in Linux

Nov 8, 2015 by Grzegorz Juszczak 0 Comments check hardware architecture linux, check system architecture linux, display hardware topology linux, display system topology linux, linux display hardware topology

Sometimes we need to know what is our system configuration (CPU, RAM, network interfaces, etc…), but we don’t want to open computer case to look what’s inside or even don’t have such possibility, especially when we are connected to remote server.

We can use lstopo command in Linux command line to quickly display system architecture.
Read More

Linux

How To Detect Physical Interface Connectivity to the Network in Linux

Nov 2, 2015 by Grzegorz Juszczak 0 Comments detect connected cable, linux ethtool detect connectivity, linux physical interface connection, network connectivity linux

How to verify, if cable is connected to the interface in Linux? How to verify physical connection to network on interface in Linux?

If you are away from the server and unable to see if ethernet cable is connected to the particular interface in server, but you have another connection (i.e.: via iLO Console), you can use ethtool to verify physical connectivity on that interface remotely.
Read More

Cloud Computing, Virtualization

Install OpenStack on KVM – How To Configure KVM for OpenStack

Oct 21, 2015 by Grzegorz Juszczak 4 Comments kvm openstack configuration, kvm openstack installation, kvm openstack network, openstack in fedora kvm, openstack kvm configuration, openstack kvm installation, openstack kvm network

Typical OpenStack cloud setup consists of more than one node (usually one Controller node and several Compute nodes), which requires lot of physical computers / servers available to perform the installation. This complicates the situation, especially if we need to test OpenStack on many nodes. Fortunately we can use Linux KVM (Kernel-based Virtual Machine) to create OpenStack on virtual nodes and avoid problems with obtaining physical hardware.

In this tutorial we will show you how to install OpenStack on KVM on Fedora 21 based hypervisor. We will run Openstack installation on two KVM based virtual nodes (Controller and Compute).

The most important part in configuring KVM for OpenStack installation is network setup, we also need to secure some resources (VCPUs, RAM, disk space) on KVM Hypervisor to create two virtual nodes.

Linux, Security

How to Disable or Enable SELinux on CentOS / Fedora / RHEL

Oct 16, 2015 by Grzegorz Juszczak 0 Comments disable enable selinux fedora, disable selinux centos redhat, manage selinux centos redhat, selinux centos redhat fedora, selinux enforcing red hat, selinux permissive enforcing mode, selinux permissive mode centos

SELinux (Security Enhanced Linux) is an additional method of Linux system protection. It’s a group of security contexts that determine which process can access which files, directories, ports, etc…

SELinux has three modes:
Enforcing: SELinux protects files, directories, ports against unauthorized access and logs all SELinux events and attempts.
Permissive: SELinux allows all interactions and context violations and logs them. Permissive mode is often used for troubleshooting SELinux.
Disabled: SELinux is completely disabled.

SELinux in Enforcing mode may cause problems accessing files or ports in the system, that’s why it’s good to know how to change it’s mode or even disable it.
Read More